DLC Cable Drag Trolley I-Beam Trolley
Dali Electric recommends
DLC Cable Drag Trolley I-Beam Trolley is used for suspending and moving cables of mobile power supply machinery during movement, and has been widely used in various lifting machinery. This device has the advantages of sturdy structure, flexible movement, and safe and reliable operation.
The trolley consists of three parts: the pulling trolley, the cable trolley, and the terminal trolley. The pulling trolley follows the cable guiding (traction) device of the mobile machinery. Each mobile machinery is equipped with one, which runs back and forth with the mobile machinery. The middle cable trolley suspends the cable within the range of the I-beam track and moves with the pulling trolley. Both ends are equipped with buffer bumpers. The number of trolleys depends on the length of movement. The terminal trolley is fixed at the end of the I-beam guide rail, generally one for each mobile machinery.
This series of trolleys is divided into five models: I, II, III, IV, and V. If users adopt 12#, 14#, 16# or larger I-beams, they can indicate it when ordering, and our factory can supply the complete set.
Product Introduction:
|
|
Product Introduction:
HC series cable trolley seriesLight load type cable conduction trolley device is used for suspending and moving cables of mobile power supply machinery during movement, and has been widely used in various lifting machinery. This device has the advantages of sturdy structure, flexible movement, and safe and reliable operation.
Light load type cable conduction trolley consists of three parts: the pulling trolley, the cable trolley, and the terminal trolley. The pulling trolley follows the cable guiding (traction) device of the mobile machinery. Each mobile machinery is equipped with one, which runs back and forth with the mobile machinery. The middle cable trolley suspends the cable within the range of the I-beam track and moves with the pulling trolley. Both ends are equipped with buffer bumpers. The number of trolleys depends on the length of movement. The terminal trolley is fixed at the end of the I-beam guide rail, generally one for each mobile machinery.
This series of trolleys is divided into five models: I, II, III, IV, and V. If users adopt 12#, 14#, 16# or larger I-beams, they can indicate it when ordering, and our factory can supply the complete set.
Product Introduction:
The HC type cable trolley series is a conductive form for power supply to crane trolleys. It consists of wheels, brackets, and support plates. The flexible cable is fixed on the support plate, and the traction frame is synchronized with the cable trolley to achieve the purpose of power supply to the trolley.
The HC series cable trolleys are divided into medium load type, heavy load type, and light load type. Therefore, the trolley wheels are of three types: Ф80, Ф63, and Ф50, with a load capacity of ≤50∽150kg. Each type is divided into single-layer, double-layer, and three-layer according to the number of support plate layers. Each type has three forms: the front end is the cable traction trolley, the terminal is the fixed wire hanging frame, and the middle is the cable trolley (see figure below).
Light load type cable conduction trolley description
1. After the fixed wire hanging frame is installed, a baffle should be hung behind it.
2. Adjust the traction head so that the trolley does not touch the upper and lower edges of the traction hole during the entire travel.
3. The cable length is 1.2 times the crane span plus 8 meters.
4. Adjust the traction steel wire rope so that its length is less than the length of the same section of cable. During operation, the traction steel wire rope bears the force.
5. When the cable diameters are different, soft rubber should be padded between the cable clamps to make their outer diameters basically the same, so as to clamp the cables tightly.
6. When laying cables, consider the balanced force on the cable support plates on both sides.
7. When the cable trolley has two or three layers, the requirements are the same.
8. The double washers on the trolley device are adjustment washers. When the guide rail is not suitable, place the washers on the inner side of the fixed plate to adjust the width of the track gauge. At the factory, it is manufactured according to the guide rails I 100*68*4.5, I 120*74*5, I140*80*5, I 160*88*6. Non-standard trolleys are processed and manufactured according to drawings.
Note: The above information and technical parameters are compiled and released by Yangzhou Dali Electric Co., Ltd.
